Post 4 - Removing the Rubrail

This last weekend, I finished removing the old rubrail on the sailboat. As you can see from this first picture, the rubrail is screwed from the outside through the hull of the boat. The screw is attached through the joint between the two halves of the boat, and then the nut on the inside of the boat is covered in fiberglass tape.

In this first picture , you can see the seam between the white bottom hull piece and the blue top deck piece, which overlaps it. These two pieces are screwed together from the outside.

After the two pieces were screwed together, the rubrail was screwed through both pieces from the outside. This effectively covers the seam on the outside of the boat. After the rubrail was screwed on, the inside seam and all the exposed screws and nuts were then taped over with fiberglass. This makes removing the rubrail a little more difficult.

In the second picture, you can see the inside taped seam, and the bulges in the seam where all the scews and nuts have been taped over. The darker holes you can see are where I have already chiseled through the fiberglass and removed the rubrail screws. The remaining bumps are the screws that attach the deck to the hull.

Even after I chiseled the fiberglass out of the way on the inside, the screws were usually too corroded to turn without stripping-out. As a result, I ended up chiseling the rubrail out of the way of the screwhead, as seen in the third picture.

I then cut off the outside screwheads with a

cutoff disk attached to my dremel tool. After the screwheads were cut off, I was able to remove the rubrail .With the rubrail removed, and the tape removed from the inside, I was then able to drive the screws out with a punch from the outside of the boat. I will be filling all these holes in with epoxy, and then I will drill new holes for the new rubrail after I have painted the outside of the boat.

In other news, I purchased a gallon of Franmar Soy Strip to aid with the paint removal. I tested it on a section of the deck by applying it about 1/8" thick and then covering it with waxed paper. After two hours, I removed the waxed paper and I was able to easily scrape the top layer of paint off. There are two layers of paint that I want to remove, so next time I will try leaving the solution on for a longer period of time before I try scraping.

Post 3 - In the Garage and Scraping Paint

The boat now sits comfortably in the garage. Much of the past few weeks was spent simply organizing the garage, so I would actually have room to work. After multiple trips to the dump and storage, the work has resumed.

Much of the boat hardware has been removed. Paint has been scraped off about half of the starboard hull. Not much at all has been scraped off the topside. For now, I am using a 2" carbide scraper. No chemicals as of yet. I will soon be ordering some, though.

Post 2 - Hurry up and Wait

Much of the last few days has been spent learning about the boat I have purchased, and learning in general about the restoration process of old fiberglass boats.Today I ordered a book entitled "This Old Boat", which is revered as a bible of sorts for people wishing to restore these type of boats.

Previous to my purchase of this boat, my study focused primarily on stitch-and-glue, and building wooden boats from the ground up. My original intention was to build a boat from scratch.

I have started sanding the interior. I figured that the interior of the boat would be a bit more forgiving; I will read-up some more before I tackle the exterior. I have also decided to move the boat into the garage. I cut some wooden skids out of 4x6 lumber and slid them under the keels. Tomorrow I will try and pull the boat off the trailer on these skids and move it into the garage. I didn't like the way the keels

were sitting on those narrow pieces of steel on the trailer. Also, It will be nice to have the boat in a more controlled environment, where I can even work at night, if I wish.

Post 1

Here Goes, my first post.

Today my wife and I completed our purchase of a Vivacity 20’ Sailboat from a guy named Aaron who lives in Heber City.

Purchase price was $650.00. It included boat, trailer, sails, anchor, and various other extras. No Motor. No Title either. He said this won’t be a problem. Most recent sticker next to the numbers is a California sticker for 1989. Perhaps that means 22 years on the hard. Will need paint stripping, minor fiberglass repair, many new fittings, all new woodwork, complete interior finishing. All new electric, as well. We are very excited. No name on the boat , either, so we will get to name it.

Wired the trailer today, in order to get it home. Trailer could use some work too, very rusty, old leaf springs, old tires. Adam had the wiring for it, so no cost there, besides cost of duct tape to temporarily secure wiring. The whole way home, I was afraid that I would get a flat.

After I made it home, I used a shop vac to vacuum water out of the bilge, along with various other leaves and debris.

Zach and I also removed the motor mount and three old wooden cleats. Aaron included some new galvanized cleats with the purchase, but I may want to go with either brass, or make some new ones out of mahogany. I will have to consider…

Downpoured on us for a while. For some reason, rain is more tolerable when you are sitting on a boat. :) I will have to get a tarp to keep it covered. I will also have to modify my side fence so I can remove it and get the Sailboat out of the driveway.

Lots of tasks before us.